{
    "article_id": 1098,
    "public_id": "71e119b5-ac9b-4cb1-b788-2ad133f3748a",
    "internal_identifier": null,
    "source_identifier": "42:103",
    "status": "published",
    "type": "research_article",
    "title": "Yarı-Katı İşlem Yöntemi ile Üretilen Al-SiC Kompozit Malzemelerin Aşınma Davranışlarının İncelenmesi",
    "title_secondary": null,
    "abstract": "Bu çalışmada, yarı-katı işlem yöntemi ile Al-SiC kompozit malzemelerin sabit yük altında aşınma davranışları incelenmiştir. A356 matrise, 4 farklı miktarda (%5, %10, %15 ve %20) SiC ilave edilmiştir. Titreşimli tip değirmende bilyesiz olarak (30 dakika) karıştırılan kompozit tozlar, soğuk preslenerek (800 MPa) green kompaktlar üretilmiştir. Üretilen green kompaktlar 550 °C kalıp sıcaklığı ve 590 °C fırın sıcaklığında 1 dakika preslenmiştir. Mikro yapı, sertlik ve küresellik oranı belirleme çalışmaları yapılmıştır. Aşınma testleri standart pin on disk aşınma test cihazında 15 N yük, 0,2 ms-1 kayma hızı ve dört farklı (500 m, 1000 m, 1500 m ve 2000 m) kayma mesafesi kullanılmıştır. Yapılan çalışmalar sonucunda, kompozit malzeme içerisinde artan SiC miktarı ile sertlik artarken, küresellik oranları ise azalmaktadır. Aşınma testleri sonucunda, en yüksek ağırlık kaybı, %5 SiC elde edilirken, en düşük ağırlık kaybı ise %20 SiC ilave kompozit malzemelerde elde edilmiştir. Bununla birlikte en düşük sürtünme katsayısı ise %20 SiC ilave edilen kompozit malzemede olduğu görülmüştür.  ",
    "language": "tr",
    "english_title": "Investigation of Wear Behaviors of Al-SiC Composite Materials Produced by Semi-Solid Process Method",
    "english_abstract": "In this study, was investigated the wear behaviors under constant load of Al-SiC composite materials produced by semi-solid processing method. In the A356 matrix, was added four different amounts (5%, 10%, 15% and 20%) SiC. Composite powders mixed without ball (30 min) in the vibrating type mill were cold pressed (800 MPa) and green compacts were produced. The produced green compacts, in 550 °C mold temperature and in 590 °C furnace temperature 1 min were pressed. Microstructure, hardness and sphericity ratio were determined. The wear tests were used a pin on-disk type wear testing device, under 15 N loads and four different sliding distances (500m, 1000m, 1500m and 2000m). As a result of the studies, the hardness increases with increasing amount of SiC in the composite material, while the sphericity rates decrease. As a result of the wear tests, while the highest weight loss was obtained from 5% SiC additional composite materials, the lowest weight loss was obtained from 20% SiC additional composite materials. In addition to , the lowest friction coefficient was obtained in the composite material added 20% SiC.",
    "doi": null,
    "doi_url": null,
    "resource_url": "https://www.set-science.com/a/71e119b5-ac9b-4cb1-b788-2ad133f3748a",
    "pdf_url": "https://www.set-science.com/a/71e119b5-ac9b-4cb1-b788-2ad133f3748a/pdf",
    "og_image": "https://www.set-science.com/assets/img/og-card-v2.png",
    "authors": [
        {
            "public_id": "2bc18dea-b210-436a-869a-5693213b9e9d",
            "given": "İjlal ",
            "family": "Şimşek  ",
            "full": "İjlal  Şimşek  ",
            "literal": null,
            "orcid": null,
            "orcid_url": null,
            "email": "dozyurek@karabuk.edu.tr",
            "corresponding": false,
            "sequence": "first",
            "affiliations": [
                {
                    "name": "Karabük Üniversitesi  ",
                    "department": null,
                    "country": null,
                    "country_code": null,
                    "ror": null,
                    "ror_url": null
                }
            ]
        },
        {
            "public_id": "a7534eaf-4ae9-4a9e-a633-482e6e3bc495",
            "given": "Doğan",
            "family": "Şimşek  ",
            "full": "Doğan Şimşek  ",
            "literal": null,
            "orcid": null,
            "orcid_url": null,
            "email": "dozyurek@karabuk.edu.tr",
            "corresponding": false,
            "sequence": "additional",
            "affiliations": [
                {
                    "name": "Bitlis Eren Üniversitesi  ",
                    "department": null,
                    "country": null,
                    "country_code": null,
                    "ror": null,
                    "ror_url": null
                }
            ]
        },
        {
            "public_id": "776d6ad9-c55c-4143-92dc-3249107e272e",
            "given": "Dursun ",
            "family": "Özyürek  ",
            "full": "Dursun  Özyürek  ",
            "literal": null,
            "orcid": null,
            "orcid_url": null,
            "email": "dozyurek@karabuk.edu.tr",
            "corresponding": true,
            "sequence": "additional",
            "affiliations": [
                {
                    "name": "Karabük Üniversitesi  ",
                    "department": null,
                    "country": null,
                    "country_code": null,
                    "ror": null,
                    "ror_url": null
                }
            ]
        }
    ],
    "keywords": [],
    "translations": [
        {
            "language": "en",
            "title": "Investigation of Wear Behaviors of Al-SiC Composite Materials Produced by Semi-Solid Process Method",
            "abstract": "In this study, was investigated the wear behaviors under constant load of Al-SiC composite materials produced by semi-solid processing method. In the A356 matrix, was added four different amounts (5%, 10%, 15% and 20%) SiC. Composite powders mixed without ball (30 min) in the vibrating type mill were cold pressed (800 MPa) and green compacts were produced. The produced green compacts, in 550 °C mold temperature and in 590 °C furnace temperature 1 min were pressed. Microstructure, hardness and sphericity ratio were determined. The wear tests were used a pin on-disk type wear testing device, under 15 N loads and four different sliding distances (500m, 1000m, 1500m and 2000m). As a result of the studies, the hardness increases with increasing amount of SiC in the composite material, while the sphericity rates decrease. As a result of the wear tests, while the highest weight loss was obtained from 5% SiC additional composite materials, the lowest weight loss was obtained from 20% SiC additional composite materials. In addition to , the lowest friction coefficient was obtained in the composite material added 20% SiC.",
            "keywords": [
                "Yarı-katı şekillendirme, A356-SiC kompozit, aşınma, sürtünme katsayısı"
            ]
        }
    ],
    "subjects": [],
    "subject_names": [],
    "published_date": "2019-06-01",
    "published_year": "2019",
    "received_date": null,
    "accepted_date": null,
    "volume": "4",
    "issue": null,
    "page_first": "545",
    "page_last": "548",
    "article_number": null,
    "conference": {
        "short_name": "ISAS2019-ENS",
        "full_title": "3rd International Symposium on Innovative Approaches in Scientific Studies (Engineering and Natural Sciences)",
        "name": "3rd International Symposium on Innovative Approaches in Scientific Studies (Engineering and Natural Sciences)",
        "acronym": "ISAS2019-ENS",
        "location": "Ankara, Türkiye",
        "start_date": "2019-04-19",
        "end_date": null,
        "public_id": "ed3b36e9-38cf-4aeb-a135-833c969cc89f"
    },
    "proceedings": {
        "title": "3rd International Symposium on Innovative Approaches in Scientific Studies (Engineering and Natural Sciences)",
        "series_title": "Setsci conference indexing system",
        "publisher": "SET Technology",
        "isbn": null,
        "eisbn": null,
        "issn": "2618-6446",
        "eissn": null,
        "doi": null,
        "doi_prefix": null,
        "slug": "setsci-volume-4-2019-legacy-42",
        "public_id": "24d215ef-a545-4351-9725-6e9bdb167b3c",
        "url": "https://www.set-science.com/p/setsci-volume-4-2019-legacy-42"
    },
    "license": {
        "name": "CC BY 4.0",
        "url": "https://creativecommons.org/licenses/by/4.0/",
        "code": "CC-BY-4.0",
        "open_access": true
    },
    "copyright": {
        "holder": "SET Technology",
        "year": "2019"
    },
    "funding_statement": null,
    "funders": [],
    "references": [
        {
            "order": 1,
            "raw": "J. W. Kaczmar, K. Pietrzak, & W. Włosiński, “The production and application of metal matrix composite materials,” Journal of Materials Processing Technology, vol. 106(1-3), pp. 58-67, 2000.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 2,
            "raw": "M. Alizadeh, M. H. Paydar, & F. S. Jazi, “Structural evaluation and mechanical properties of nanostructured Al/B4C composite fabricated by ARB process.” Composites Part B: Engineering, 44(1), 339-343, 2013.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 3,
            "raw": "I. Mutlu, O. Eldogan, & F. Findik, “Tribological properties of some phenolic composites suggested for automotive brakes,” Tribology International, vol. 39(4), pp. 317-325, 2006.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 4,
            "raw": "U. Soy, A. Demir, & F. Findik, Friction and wear behaviors of Al-SiC-B4C composites produced by pressure infiltration method. Industrial Lubrication and Tribology, vol. 63(5), pp. 387- 393, 2011.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 5,
            "raw": "T. S. Srivatsan, I. A. Ibrahim, F. A. Mohamed, & E. J. Lavernia, “Processing techniques for particulate-reinforced metal aluminium matrix composites,” Journal of Materials Science, vol. 26(22), pp. 5965-5978, 1991.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 6,
            "raw": "H. S. Lee, J. S. Yeo, S. H. Hong, D. J. Yoon, & K. H. Na, “The fabrication process and mechanical properties of SiCp/Al–Si metal matrix composites for automobile air-conditioner compressor pistons,” Journal of Materials Processing Technology, vol. 113(1-3), pp. 202-208, 2001.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 7,
            "raw": "E. J. Zoqui, M. Paes, & M. H. Robert, “Effect of macrostructure and microstructure on the viscosity of the A356 alloy in the semisolid state,” Journal of Materials Processing Technology, vol. 153, pp. 300-306, 2004.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 8,
            "raw": "H. V. Atkinson, & D. Liu, “Microstructural coarsening of semisolid aluminium alloys,” Materials Science and Engineering: A, vol. 496(1-2), pp. 439-446, 2008.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 9,
            "raw": "M. Paes, & E. J. Zoqui, “Semi-solid behavior of new Al–Si–Mg alloys for thixoforming,” Materials Science and Engineering: A, vol. 406(1-2), pp. 63-73, 2005.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 10,
            "raw": "H. Aztekin, D. Ōzyūrek, & K. Çetinkaya, “Production of hypoeutectic Αl-Si alloy based metal matrix composite with thixomoulding processing,” High Temperature Materials and Processes, vol. 29(3), pp. 169-178, 2010.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 11,
            "raw": "D. Özyürek, M. Yıldırım, & İ. Çiftçi, “The tribological properties of A356-SiCp metal-matrix composites fabricated by thixomoulding technique,” Science and Engineering of Composite Materials, vol. 19(4), pp. 351-356, 2012.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 12,
            "raw": "K. S. Alhawari, M. Z. Omar, M. J. Ghazali, M. S. Salleh, & M. N. Mohammed, “Microstructural evolution during semi solid processing of Al-Si-Cu alloy with different Mg contents,” Transactions of Nonferrous Metals Society of China, vol. 27(7), pp. 1483-1497, 2017.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 13,
            "raw": "İ. Şimşek, M. Yıldırım, T. Tunçay, D. Özyürek, & D. Şimşek, “Mekanik alaşımlama/öğütme yöntemi ile üretilen Al-SiC kompozitlerin incelenmesi,” Technological Applied Sciences, vol. 13(2), pp. 165-171, 2018.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 14,
            "raw": "İ. Şimşek, D. Şimşek, & D. Özyürek, “Production and characterization of Al-SiC composites prepared by mechanical milling and pressureless sintering,” BEÜ Fen Bilimleri Dergisi, vol. 8(1), pp. 227-233, 2019.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 15,
            "raw": "M. Moazami-Goudarzi, & F. Akhlaghi, “Wear behavior of Al 5252 alloy reinforced with micrometric and nanometric SiC particles,” Tribology International, vol. 102, pp. 28-37, 2016.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 16,
            "raw": "S. Mosleh-Shirazi, F. Akhlaghi, & D. Y. Li, “Effect of SiC content on dry sliding wear, corrosion and corrosive wear of Al/SiC nanocomposites,” Transactions of Nonferrous Metals Society of China, vol. 26(7), pp. 1801-1808, 2016.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        },
        {
            "order": 17,
            "raw": "A. Karthikeyan, & S. Nallusamy, “Experimental analysis on sliding wear behaviour of aluminium-6063 with SiC particulate composites,” In International Journal of Engineering Research in Africa, Trans Tech Publications, vol. 31, pp. 36-43, 2017.",
            "doi": null,
            "title": null,
            "authors": null,
            "source": null,
            "year": null,
            "volume": null,
            "pages": null
        }
    ],
    "statements": {
        "acknowledgements": null,
        "conflict_of_interest": null,
        "data_availability": null,
        "ai_disclosure": null
    },
    "credit": [],
    "history": {
        "published": "2019-06-01"
    }
}