Search

The aim of this study is to forecast installed wind power which is a one of the renewable energy resources in Turkey for the year of 2017 based on artificial neural network method using the normalized last ten-year data. An artificial neural network has been c…

Exhaust gas distribution in street canyons is one of the important research subjects in urban air quality studies. Vehicle emissions are an important group of pollutants in urban areas. In this study, the dispersion of exhaust emissions from vehicles in canyon…

This paper describes a laboratory application for the forecasting the dielectric properties, using an artificial neural network embedded in a microprocessor. The dielectric permittivity and loss factor of the insulation material were determined as a function o…

Elektromanyetik alanların canlılar üzerindeki zararlı etkileri bugün için bilimsel çevreler tarafından en çok üzerinde durulan ve araştırmalar yapılan konulardan biridir. Elektrik enerjisi ile çalışan cihaz ve sistemler çevresine elektromanyetik enerji yaymakt…

In this study, the experimental application of polymer electrolyte membrane fuel cell (PEM-FC) with dc-dc boost converter is realized for compact design of electric vehicle (eV). The PEM-FC is an electro-chemical device which combines hydrogen with oxygen to p…

In this study, we focused on to drive a compound DC motor with a Fuel-Cell and battery, which uses hydrogen as a fuel. A fuel cell can supply maximum 40V electric. In order to drive a DC motor, it needs 200Vdc. Therefore, a microcontroller controlled boost con…

Analysis of faults in synchronous generators are so important to protect the generators and the power systems. In this paper, double line-to-ground fault analysis in unloaded synchronous generator is presented. Apart from the similar studies in the literature,…

The importance of the service quality has increased because of the rapid development of the technology and globalization. In the global competition environment, teaching of the students that can provide the expectations of the society and the business world is…

The structure of the gas diffusion layer influences cell performance because it also affects the passage of reaction gases and electrons. In this study, the effect of the thickness of the gas diffusion layer on the cell performance for the singlecelled PEM fue…

In the study synchronization was studied using an all-to-all network structure in a multiple system of Kuramoto oscillators. Synchronization performance was first investigated in a weakly connected system, and the effects of link strength and number of oscilla…

In this article, the influence of the use of three different bricks on the building heat performance is compared for use on wall surfaces as a building construction element. At the beginning of the analysis, the thermal analysis of the building was carried out…

3D printing filling structures at prototyping and design stage are increasingly important issue for products with complicated shapes. The objective of the present study is to investigate 3D printing filling structures effect on mechanical properties and surfac…

In this study, the elimination of zero diffraction order and twin image from three dimensional reconstructed images in digital holography and the image enhancement are desired to achieve in a short time by using hybrid methods. In addition, the brightness of t…

The aim of this study is to determine instantaneous irradiance and annual percentile sunlit time on the available rooftop floor area of Technical and Social Science Vocational School at Usak University by simulation using open source software. The building of …

Innovations, which are one of the most important identifiers of pass to information society, have caused socio-economic transformations on global level. Especially labour factor, which companies use in production, have been affected by innovations. On the grou…

For a successful thermal performance, the right choice and design of the thermal management materials used in LED die-moulding, cooler and soldered parts is a critical engineering problem. Because they are affected by heat emitted from the pn junction in the L…

In this paper, a structural-output is obtained to estimate 3D human pose using 3D human point cloud and monocular images. The Neural Network takes a human image and 3D pose as inputs and gives outputs a score value. Conditional Random Field (CRF) approach is u…

In this study, research on the determination of the technological level in the greenhouse mechanization in Southeastern Anatolia Region of Turkey has been carried out. The technological equipment and operating parameters that should be in a modern greenhouse h…

In the present study, the effects of cutting parameters on surface roughness were investigated in order to determine the optimum machining conditions for the hot work tool steel (155 HB), which is an important part of the mold industry. For this purpose, the m…