Stronsiyum ve Stronsiyum-Magnezyum katkılarının Al-9Si Alaşımının Yapısal ve Mekanik Özelliklerine Etkisi
Abstract
Bu çalışmada birer adet ikili Al-9Si, üçlü Al-9Si-0,1Sr ve dörtlü Al-9Si-0,1Sr-0,6Mg alaşımı indüksiyonlu ergitme ocağında ergitme ve oda sıcaklığında tutulan kokil kalıba döküm yöntemi ile üretildi. Alaşımların yapısal ve mekanik özellikleri üretilen alaşım külçelerinden talaşlı imalat yöntemiyle hazırlanan numuneler üzerinde yapılan incelemeler ile belirlendi. İçyapı incelemeleri standart metalografik yöntemler ile hazırlanan ancak dağlama yapılmayan numuneler üzerinde gerçekleştirildi. Sertlik değerleri Brinell sertlik ölçüm yöntemi, akma ve çekme dayanımı ile kopma uzaması değerleri ise universal bir çekme deneyi makinesinde yapılan testler yardımıyla belirlendi. İkili Al-9Si alaşımının içyapısının alüminyumca zengin α dendiritleri, primer silisyum, ötektik Al-Si fazlarından oluştuğu, üçlü Al-9Si-0,1Sr alaşımının içyapısında ise ikili Al-9Si alaşımındaki fazlara ek olarak AlxSiySrz fazı oluştuğu görüldü. Üçlü Al-9Si-0,1Sr alaşımına %0,6 oranında yapılan magnezyum katkısının ise içyapıyı belirgin bir şekilde etkilemediği görüldü. Al-9Si alaşımına %0,1 oranında yapılan stronsiyum katkısının sertliği çok az da olsa düşürdüğü, akma ve çekme dayanımı ve kopma uzaması değerlerini ise iyileştirdiği görüldü. Üçlü Al-9Si-0,1Sr alaşımına yapılan magnezyum katkısının ise akma ve çekme mukavemetini önemli ölçüde artırırken, kopma uzaması değerini azalttığı görüldü. Stronsiyum ve stronsiyum-magnezyum katkılarının ikili Al-9Si alaşımının sertlik, akma ve çekme mukavemeti ile kopma uzaması değerlerinde yol açtığı değişimler yapısal özelliklerine dayandırılarak açıklandı.
English-language details
Effect of Strontium and Strontium-Magnesium Additives on the Structural and Mechanical Properties of Al-9Si Alloy
In this study, one binary Al-9Si, one ternary Al-9Si-0.1Sr, and one quaternary Al-9Si-0.1Sr-0.6Mg alloy were produced by melting in an induction melting furnace and casting into a room temperature mold. The structural and mechanical properties of the alloys were determined by examining samples prepared from the produced alloy ingots using machining methods. Microstructure examinations were performed on samples prepared using standard metallographic methods but without etching. Hardness values were determined using the Brinell hardness test method, while yield and tensile strength and elongation at fracture values were determined using tests performed on a universal tensile testing machine. It was observed that the microstructure of the binary Al-9Si alloy consisted of aluminum-rich α dendrites, primary silicon, and eutectic Al-Si phases, while the microstructure of the ternary Al-9Si-0.1Sr alloy included the AlxSiySrz phase in addition to the phases found in the binary Al-9Si alloy. Adding 0.6% magnesium to the ternary Al-9Si-0.1Sr alloy did not significantly affect the microstructure. Adding 0.1% strontium to the Al-9Si alloy slightly reduced hardness but improved yield and tensile strength and elongation at fracture. Adding magnesium to the ternary Al-9Si-0.1Sr alloy significantly increased yield and tensile strength while decreasing elongation at fracture. The changes in hardness, yield strength, tensile strength, and elongation at fracture of binary Al-9Si alloy caused by strontium and strontium-magnesium additions were explained based on their structural properties.
Keywords
Cite this article
Hekimoğlu, A. P., Çalış, M., & Ayata, G. (2018). Effect of Strontium and Strontium-Magnesium Additives on the Structural and Mechanical Properties of Al-9Si Alloy. In Ist International Symposium on Innovative Approaches in Scientific Studies (pp. 422–426). SET Technology.
Article History
- Published
- 23 Jun 2018
License
© 2018 SET Technology. This article is distributed under the terms of the CC BY 4.0.