T5 ve T7 Isıl İşlemlerinin Zn-15Al-3Cu-1Si Alaşımının Yağlı Çalışma Koşullarındaki Sürtünme ve Aşınma Özelliklerine Etkilerinin İncelenmesi

References

1. T. Savaşkan, and Y. Alemdağ, “Effects of pressure and sliding speed on the friction and wear properties of Al-40Zn-3Cu-2Si alloy: A comparative study with SAE 65 bronze,” Mat Sci Eng A-Struct, vol. 496, pp. 517 ̶ 523, Nov. 2008.
2. B. K. Prasad, “Sliding wear response of a zinc-based alloy and its composite and comparison with a gray cast iron: influence of exeternal lubrication and microstructural features,” Mat Sci Eng A-Struct, vol. 392, pp. 427 ̶ 439, Feb. 2005.
3. P. Delneuville, “Tribological behaviour of Zn-Al alloys (ZA27) compared with bronze when used as a bearing material with high load and very low speed,” Wear, vol. 105, pp. 283 ̶ 292, Oct. 1985.
4. F. E. Goodwin, and A. L. Ponikvar, Engineering Properties of Zinc Alloys, International Lead Zinc Research Organization, 3nd, USA, 1989.
5. E. Gervais, R. J. Barnhurst, and C. A. Loong, “An analysis of selected properties of ZA alloys,” Jom-J Min Met Mat S, vol. 37, pp. 43 ̶ 47, Nov. 1985.
6. W. Köster, and K. Moeller, “The constitution and volume changes of Zn-Cu-Al alloys. V. The division of the ternary phases at low temperatures,” Z. Metallkd., vol. 34, pp. 206 ̶ 207, 1942.
7. W. Köster, and K. Moeller, “On the synthesis and constitution of zinccopper-aluminum alloys. II. The correlation of CuAl with the ternary crystalline phase,” Z. Metallkd., vol. 33 pp. 284 ̶ 288, 1941.
8. W. Köster, On the synthesis and constitution of alloys of brass. III. Review of the equilibrium in copper-aluminum-zinc System, Z. Metallkd., vol. 33, pp. 289 ̶ 296, 1941.
9. A. P. Hekimoğlu, “Bakır ve/veya silisyum içeren Zn-15Al esaslı alaşımların yapısal, mekanik ve tribolojik özelliklerinin incelenmesi” PhD thesis, Karadeniz Teknik Üniversitesi, Trabzon, Türkiye, Tem. 2013.
10. T. Savaşkan, and A. P. Hekimoğlu, “Effect of quench ageing treatment on the microstructure and properties of Zn-15Al-3Cu alloy,” Int J Mater Res., vol. 106, pp. 481̶ 487, Feb. 2015.
11. A. P. Hekimoğlu, and T. Savaşkan, “Zn-15Al-3Cu-1Si alaşımı ve SAE 660 bronzunun yağlı durumdaki aşınma karakteristikleri,” J Fac Eng Archit Gaz., vol. 33, pp. 145 ̶ 154, 2018.
12. A. P. Hekimoğlu, and T. Savaşkan, “Effects of contact pressure and sliding speed on the unlubricated friction and wear properties of Zn- 15Al-3Cu-1Si alloy,” Tribol T., vol. 59, pp. 1114 ̶ 1121, Apr. 2016
13. T. Savaşkan, and A. P. Hekimoğlu, “Relationships between mechanical and tribological properties of Zn-15Al based ternary and quaternary alloys,” Int J Mater Res., vol. 107, pp. 646 ̶ 652, Jun. 2016.
14. T. Savaşkan, and A. P. Hekimoğlu, “Microstructure and mechanical properties of Zn-15Al based ternary and quaternary alloys,” Mat Sci Eng A-Struct., vol. 603, pp. 52 ̶ 57, May. 2014.
15. B. K. Prasad, “Influence of heat treatment parameters on the lubricated sliding wear behaviour of a zinc based alloy,” Wear, vol. 257, pp. 1137 ̶1144, Dec. 2004.
16. M. T. Jovanoviç, I. Bobiç, B. Djuriç, N. Grohovac, and N. Iliç, “Microstructural and sliding wear behaviour of a heat-treated zincbased alloy,” Tribol Lett., vol. 25, pp. 173 ̶ 184, Oct. 2007.
17. B. Bobic, S. Mitrovic, M. Babic, A. Vencl, and I. Bobic, “Corrosion behavior of the as-cast and heat-treated ZA27 alloy,” Tribology in Industry, vol. 33, pp. 87 ̶ 93, Jun. 2011.
18. T. Savaşkan, and O. Bican, “Effects of silicon content on the microstructural features and mechanical and sliding wear properties of Zn-40Al-2Cu-(0-5)Si alloys,” Mat Sci Eng A-Struct., vol. 404, pp. 259 ̶ 269, Sep. 2005.
19. O. Bican, and T. Savaşkan, “Influence of test conditions on the lubricated friction and wear behaviour of Al-25Zn-3Cu alloy,” Tribol Lett., vol. 37, pp. 175 ̶ 182, Feb. 2010.
20. S. Murphy, and T. Savaşkan, “Comparative wear behaviour of Zn-Albased alloys in an automotive engine application,” Wear, vol. 98, pp 151–161,